Welcome! Becoming a registered user of ShortWingPipers.Org is free and easy! Click the "Register" link found in the upper right hand corner of this screen. It's easy and you can then join the fun posting and learning about Short Wing Pipers!

Results 1 to 7 of 7

Thread: Clipper Aileron cable through cabin area question.

  1. #1

    Join Date
    May 2016
    Posts
    214
    Post Thanks / Like

    Default Clipper Aileron cable through cabin area question.

    I can't find any good drawings in the PA16 CD. The aileron cable that runs through the cabin is rubbing on the diagonal tube just above the rear window on BOTH Sides. I see the place where the trim strip attaches to but I don't see an area for a fair lead if there's supposed to be one, as there's no drawings for that area. The cable rubs slightly on both sides but I know it's not correct.



    Does anyone know how it's supposed to go? I just installed the wings and have the rigging correct, today I installed the ailerons and found this issue.

  2. #2

    Join Date
    May 2016
    Location
    CGX
    Posts
    716
    Post Thanks / Like

    Default Re: Clipper Aileron cable through cabin area question.


  3. #3
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    15,454
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Clipper Aileron cable through cabin area question.

    You probably need the fair leads at the rear spar to fuselage attach.
    20171208_182129.jpg

    20171208_182122.jpg

    20171208_182107.jpg

  4. #4

    Join Date
    May 2016
    Posts
    214
    Post Thanks / Like

    Default Re: Clipper Aileron cable through cabin area question.

    Thanks Steve that's exactly what I need that I don't have. Are those in the plans so I could make my own or know
    where I could find a set? Do the Pacers and Tripacers use those too, if so maybe I could find a set used?

    Thanks!

  5. #5
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    15,454
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Clipper Aileron cable through cabin area question.

    I have not seen them available anywhere. Comonly misplaced from what I have seen over the years. I made these. It is the width of the nylon fairlead, have to measure the length.

  6. #6

    Join Date
    May 2016
    Posts
    214
    Post Thanks / Like

    Default Re: Clipper Aileron cable through cabin area question.

    Quote Originally Posted by Steve Pierce View Post
    I have not seen them available anywhere. Comonly misplaced from what I have seen over the years. I made these. It is the width of the nylon fairlead, have to measure the length.
    Thanks, I guess I could make my own. I guess my project either never had them or mine were lost but not sure how as everything was put in a box.

    I have two two odd looking tabs that I don't know where they go, could the stock faileads look different?

    Going to the hangar and double check, but I look forward to your measurements!

  7. #7
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    15,454
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Clipper Aileron cable through cabin area question.

    I sent you a PM but never heard back. Found my jig to make the part today.
    20180106_135517.jpg

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •