Welcome! Becoming a registered user of ShortWingPipers.Org is free and easy! Click the "Register" link found in the upper right hand corner of this screen. It's easy and you can then join the fun posting and learning about Short Wing Pipers!

Thanks Thanks:  0
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23

Thread: Tail wheel arm, PA16

  1. #11
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    13,283
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Tail wheel arm, PA16

    Quote Originally Posted by JohnD View Post
    these eyebolts, does anyone know the part nr for them?
    Part number for the eye bolt is in the link I posted.

  2. #12
    JohnD's Avatar
    Join Date
    Apr 2014
    Location
    North Iceland
    Posts
    50
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    thank you.

  3. #13
    Just Call Me Al's Avatar
    Join Date
    Aug 2015
    Posts
    63
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    Quote Originally Posted by Steve Pierce View Post
    What is T,T,O,C,S?
    This kind with this kind of price.
    https://www.aircraftspruce.com/catal...rudderarms.php

  4. #14
    JohnD's Avatar
    Join Date
    Apr 2014
    Location
    North Iceland
    Posts
    50
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    There are way too many AN42B bolts to choose from, does anyone know which one would be the right fit for a PA16? I am placing an order for the scott arm and wanted to include the bolts..

  5. #15
    Just Call Me Al's Avatar
    Join Date
    Aug 2015
    Posts
    63
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    The less expensive arm that I noted above will use an AN43B-6. The Scott 1140 arm will use an AN42B-6.

  6. #16
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    13,283
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Tail wheel arm, PA16

    Like called out in the linked thread I have always used the -7 with an AN960-10 washer and an AN310-3 nut and cotter pin so it can rotate a bit.

  7. #17
    59pacer's Avatar
    Join Date
    Feb 2010
    Location
    Mulgoa, Australia
    Posts
    412
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    I would also check that the holes in the rudder itself are not worn as well. I am talking about the holes between the rudder and the arm. The holes where the springs attach have a bushing and have seen those drilled out and a larger bushing installed and it broke off.

    https://www.shortwingpipers.org/foru...onnector-Clips

    Rather than use AN3 bolts to attach the bracket to the rudder, I taper reamed and used AN386 taper pins with AN 975 taper pin washers. After about 800 hours of hard work, at the last annual, for the first time, I had to take up the taper pin nuts by 1/3 of a turn and they are completely rigid again. You need to take a lot of care with a taper reamer. My old (recently departed at 97years) engineer mate said 'taper reamers go not enough, not enough, @#** too much!'.
    Last edited by 59pacer; 06-07-2019 at 11:55 PM.

  8. #18

    Join Date
    Apr 2008
    Location
    Midway Utah
    Posts
    174
    Post Thanks / Like

    Default Scott rudder arm 1140

    Hi all. Would like to replace my Scott Rudder Arm 1140. Have determined that mine is slightly twisted. Univair has one but not sure if it is correct. Also not sure how long the shank should be. Please advise.

  9. #19
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    13,283
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Scott rudder arm 1140

    Quote Originally Posted by clipquito View Post
    Hi all. Would like to replace my Scott Rudder Arm 1140. Have determined that mine is slightly twisted. Univair has one but not sure if it is correct. Also not sure how long the shank should be. Please advise.
    I merged your thread with another on the same subject. Good info in the previous posts.

  10. #20

    Join Date
    Apr 2008
    Location
    Midway Utah
    Posts
    174
    Post Thanks / Like

    Default Re: Tail wheel arm, PA16

    Hello. Did you ever find out the part number for the AN42 eyebolt? North Iceland ... wow!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •