Welcome! Becoming a registered user of ShortWingPipers.Org is free and easy! Click the "Register" link found in the upper right hand corner of this screen. It's easy and you can then join the fun posting and learning about Short Wing Pipers!

Thanks Thanks:  0
Likes Likes:  0
Results 1 to 6 of 6

Thread: Bottom Rub Strip

  1. 01-11-2023, 11:44 PM #1
    chicobushmaster
    chicobushmaster is offline
    Join Date
    Jan 2019
    Location
    Chico, CA
    Posts
    82
    Post Thanks / Like
    Blog Entries
    1

    Default Bottom Rub Strip

    Does anyone have a drawing for the bottom rub strip for the elevator cables?
    Reply With Quote Reply With Quote
    0 0
     
  2. 01-12-2023, 07:53 AM #2
    Steve Pierce
    Steve Pierce is offline
    Administrator Steve Pierce's Avatar
    Join Date
    Nov 2007
    Location
    Graham, Texas, United States
    Posts
    14,759
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Bottom Rub Strip

    I don't know that part.
    Steve Pierce

    Support Short Wing Pipers.org- Click Here To Find Out More.
    Reply With Quote Reply With Quote
    0 0
     
  3. 01-12-2023, 02:25 PM #3
    chicobushmaster
    chicobushmaster is offline
    Join Date
    Jan 2019
    Location
    Chico, CA
    Posts
    82
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Bottom Rub Strip

    Quote Originally Posted by Steve Pierce View Post
    I don't know that part.
    It's forward of the three rollers that two cables go to the elevator, and the one that goes to the flaps
    Reply With Quote Reply With Quote
    0 0
     
  4. 01-12-2023, 03:01 PM #4
    stevesaircraft(Bri)
    stevesaircraft(Bri) is offline
    Join Date
    Nov 2007
    Location
    Beagle, Oregon (Medford) United States
    Posts
    1,276
    Post Thanks / Like

    Default Re: Bottom Rub Strip

    Its a simple piece. I have mode them out of UMHW sheet and a band saw.

    Brian
    Reply With Quote Reply With Quote
    0 0
     
  5. 01-19-2023, 02:29 PM #5
    chicobushmaster
    chicobushmaster is offline
    Join Date
    Jan 2019
    Location
    Chico, CA
    Posts
    82
    Post Thanks / Like
    Blog Entries
    1

    Default Re: Bottom Rub Strip

    I figured that I would have to do that. Thanks
    Reply With Quote Reply With Quote
    0 0
     
  6. 01-19-2023, 10:10 PM #6
    Jim Hann
    Jim Hann is offline
    Jim Hann's Avatar
    Join Date
    Mar 2013
    Location
    Ballwin (St. Louis), Missouri
    Posts
    1,582
    Post Thanks / Like

    Default Re: Bottom Rub Strip

    Quote Originally Posted by chicobushmaster View Post
    Does anyone have a drawing for the bottom rub strip for the elevator cables?
    I ordered one from Univair before Covid, it is a simple block and I would go the route that Brian suggests if I was doing it again!
    1957 PA-22/20 "Super Pacer" based 1H0
    Lifetime EAA member
    Vintage Aircraft Association member
    Lifetime EAA Chapter 32 member

    Reply With Quote Reply With Quote
    0 0
     
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules